Change in crown inclination accompanying initial tooth alignment with round archwires

ABSTRACT Objective: To evaluate, in-vitro, the change in crown inclination that occurs during orthodontic leveling and alignment using different archwire-bracket-ligation combinations. Materials and Methods: Four archwire types were tested: (1) 0.012-in stainless steel and (2) 0.0155-in stainless steel multi-stranded, (3) 0.012-in nitinol Orthonol® and (4) 0.012-in nitinol Thermalloy®. Combinations with five types of 0.022-in slot orthodontic brackets were tested: SmartClipTM and Time3® self-ligating brackets, Mini-Taurus® and Victory SeriesTM conventional brackets, and Synergy® conventional-low friction bracket. Conventional brackets were ligated with both stainless steel and elastomeric ligatures. The simulated malocclusion comprised 2.0mm gingival and 2.0mm labial displacements of a maxillary right central incisor. Rotation around the Y-axis (representing labio-palatal inclination) was measured for the different archwire-bracket-ligation combinations. Results: The largest rotation was measured whith Orthonol® and Thermalloy® wires when combined with SmartClipTM brackets (8.07±0.24º and 8.06±0.26º, respectively) and with Synergy® brackets ligated with stainless steel ligatures (8.03±0.49º and 8.0±0.37º, respectively). The lower rotation was recorded when Thermalloy®, multi-stranded, and Orthonol® wires were ligated with elastomeric rings to Mini-Taurus® brackets (1.53±0.18º, 1.65± 0.23º and 1.70±0.28º, respectively) and to Victory SeriesTM brackets (1.68± 0.78º, 2.92± 1.40º and 1.74±0.46º, respectively). Conclusions: All archwire-bracket-ligation combinations produced lingual crown inclination; however, lower changes were observed when the conventional brackets were ligated with elastomeric rings. The multi-stranded archwire produced less rotation with nearly every bracket-ligation combination, compared to the other archwires. The effect of the archwire-bracket-ligation combination on tooth inclination during leveling and alignment should be considered during planning treatment mechanics.

RESUMO Objetivo: Avaliar, in vitro, as mudanças na inclinação das coroas dentárias que acontecem durante o alinhamento e nivelamento usando diferentes combinações de arcos/braquetes/ligaduras. Material e Métodos: Foram usados quatro tipos de arcos ortodônticos: (1) 0,012" de aço inoxidável, (2) 0,0155" de aço multifilamentado, (3) Orthonol® 0,012" de nitinol e (4) Thermalloy® 0,012" de nitinol. Esses arcos foram combinados com cinco tipos de braquetes ortodônticos com slot 0,022": braquetes autoligáveis SmartClipTM e Time3®, braquetes convencionais Mini-Taurus® e Victory SeriesTM, e braquetes convencionais de baixo atrito Synergy®. Os braquetes convencionais receberam ligaduras de aço ou elastoméricas. A má oclusão simulada foi composta por um deslocamento do incisivo central superior direito em 2 mm para a cervical e 2 mm para a vestibular. A rotação ao redor do eixo Y (representando a inclinação vestibulolingual) foi medida para as diferentes combinações de arco/braquete/ligadura. Resultados: A maior rotação foi medida quando os arcos Orthonol® e Thermalloy® foram usados com os braquetes SmartClipTM (8,07±0,24º e 8,06±0,26º, respectivamente) e com os braquetes Synergy® com ligaduras metálicas (8,03±0,49º e 8,0±0,37º, respectivamente). A menor rotação foi vista quando os arcos Thermalloy®, multifilamentado e Orthonol® foram presos por ligaduras elastoméricas aos braquetes Mini-Taurus® (1,53±0,18º, 1,65±0,23º e 1,70±0,28º, respectivamente) e aos braquetes Victory SeriesTM (1,68±0,78º, 2,92±1,40º e 1,74±0,46º, respectivamente). Conclusões: todas as combinações arco-braquete-ligadura produziram inclinação palatina da coroa. Entretanto, as menores mudanças foram observadas quando os braquetes convencionais receberam ligaduras elastoméricas. O arco multifilamentado produziu menor rotação com quase todas as combinações braquete-ligadura, em comparação aos outros arcos. O efeito da combinação arco-braquete-ligadura na inclinação dentária durante o alinhamento e nivelamento deve ser considerado durante o planejamento da mecânica dos tratamentos.

Von Mises stresses on Mushroom-loop archwires for incisor retraction: a numerical study

ABSTRACT Objective: To perform a numerical simulation using FEM to study the von Mises stresses on Mushroom archwires. Methods: Mushroom archwires made of titanium-molybdenum alloy with 0.017 x 0.025-in cross-section were used in this study. A YS of 1240 MPa and a Young's modulus of 69 GPa were adopted. The archwire was modeled in Autodesk Inventor software and its behavior was simulated using the finite element code Ansys Workbench (Swanson Analysis Systems, Houston, Pennsylvania, USA). A large displacement simulation was used for non-linear analysis. The archwires were deformed in their extremities with 0° and 45°, and activated by their vertical extremities separated at 4.0 or 5.0 mm. Results: Tensions revealed a maximum of 1158 MPa at the whole part of the loop at 5.0mm of activation, except in a very small area situated at the top of the loop, in which a maximum of 1324 Mpa was found. Conclusions: Mushroom loops are capable to produce tension levels in an elastic range and could be safely activated up to 5.0mm.

RESUMO Objetivo: Realizar uma simulação numérica, por meio do Método dos Elementos Finitos (MEF), para obter as tensões de von Mises em arcos Mushroom. Métodos: Foram usados arcos com geometria Mushroom de titânio-molibdênio, com secção transversal 0,017" x 0,025". Adotou-se valores de tensão de escoamento (σesc) de 1.240 MPa e módulo de elasticidade (E) de 69 GPa. O arco foi modelado por meio do software Autodesk Inventor, e seu desempenho foi simulado utilizando-se o software de elementos finitos Ansys Workbench (Swanson Analysis System, Houston, Pennsylvania, EUA). Para a simulação, foi considerada a análise para grandes deslocamentos. O arco foi conformado em suas extremidades considerando-se planos de 0° e 45°, pré-ativado em 2,5mm e ativado por meio de suas extremidades verticais, separadas 4,0 mm ou 5,0 mm. Resultados: As tensões revelaram um valor máximo de 1.158 MPa na maior parte da alça, aos 5,0 mm de ativação, com exceção de uma área muito pequena, com valor de 1.324 MPa, situada no topo da alça. Conclusões: Os arcos Mushroom são capazes de produzir níveis de tensão situados dentro da região elástica e poderiam ser ativados com segurança até os 5,0 mm de ativação.

Preliminary Result of Randomised Controlled Trial of Three Different Coated Archwires Part 1: Tooth Alignment and Coating Loss

@#Introduction: Coated archwires improve aesthetics during orthodontic treatment. However, little is known regarding their clinical benefit. This randomised controlled trial (RCT) compared the tooth alignment (TA), coating loss (CL), colour change (∆E*), and patient perception of coated archwires with their controls. Details of ∆E* and perception were reported in the second part of the articles. Methods: This RCT was done at three centres. Participants were randomised to receive one of four treatment interventions using 0.014” superelastic coated nickel-titanium archwires from Orthocare, RMO, G&H, and conventional uncoated 3M Unitek® archwires. These archwires were ligated during bonding and collected after eighth week and questionnaires were distributed to participants in the experimental groups only. After removal, TA and CL were measured using Little’s Irregularity Index and Autodesk® AutoCAD® software, respectively. At the time of this preliminary reporting, 84 participants had completed the trial. Two archwires fractured and were excluded. Therefore, 166 archwires (n = 166) were analysed. Results: Only non-extraction cases showed statistically significant differences in TA change between all groups (p = 0.005) and RMO showed significantly lowest mean of TA (1.5 mm). RMO and Orthocare showed significant TA change in the upper and lower arches (p = 0.037, 0.048). CL was found to be insignificant for both extraction and non-extraction cases (p >0.05). Comparison between upper and lower arches revealed no significant difference in TA and CL in all groups (p >0.05). Conclusion: From this preliminary analysis, Orthocare provides better TA in non-extraction cases despite highest percentage of coating loss.

Preliminary Result of Randomised Controlled Trial of Three Different Coated Archwires Part 2: Colour Change and Patient Perception

@#Introduction: Coated archwires improve aesthetics because of the tooth-coloured appearance. However, colour change of the coated archwires have been reported in vitro. Nonetheless, little is known to what extent this colour change occurs clinically. This second part of the multi-centre, double-blind, randomised controlled trial evaluated the colour change (∆E*) of three coated archwires with their controls and patient perception. Methods: 84 patients who received treatment with upper and lower fixed appliance treatment were invited. Consented patients were randomised to receive one of four treatment interventions using 0.014” superelastic nickel-titanium archwires from (1) Orthocare (2) RMO (3) G&H, and (4) 3M Unitek® uncoated. These archwires were ligated during bonding and collected after 8th week. After removal, the digital images of the archwires were assessed for colour change using Adobe® Photoshop® software, and the CIE L*a*b* system was used to calculate the ΔE* values. Patient perception was measured using oral aesthetic subjective impact scale (OASIS) questionnaire. Results: For colour change and patient perception assessment, 132 archwires from 66 participants who had been treated with aesthetic archwires were collected. Two fractured archwires were excluded. Initial analysis revealed all three aesthetic archwires groups showed significant mean of ∆E* with the highest was found in Orthocare (23.9), and the lowest is G&H (16.8). Post hoc comparison revealed statistically significant mean of ∆E* in Orthocare when compared with other groups (p <0.001). There was no statistically significant difference for patient perception between archwire groups. Conclusion: Preliminary results revealed that significant ∆E* in Orthocare group and patients showed positive perception following clinical use

Biomechanical analysis of micro-implants lingual straight wire appliance during retracting maxillary anterior teeth / Análisis biomecánico de microimplantes con dispositivo de alambre recto lingual durante la retracción de dientes maxilares anteriores

This study aimed to establish three-dimensional finite element models of micro-implants-lingual straight wire appliance and to investigate the effects of different wire patterns on the initial displacement of the maxillary anterior teeth and the stress of the periodontal ligament and tooth root during retracting maxillary anterior teeth in lingual orthodontics. A three-dimensional geometric models of maxilla with maxillary dentition was established using Cone-beam CT scan .Three types of maxilla models including microimplants and Duet-Slot Lingual Bracket appliance with three different arch wires ( model A: 0.016 inch × 0.022 inch stainless steel square wire; modelB: 0.016 inch stainless steel round wire; model C: double wire of 0.016 inch × 0.022 inch stainless steel square wire + anterior teeth 0.016 inch stainless steel round wire) were assembled by Unigraphics NX 8.5 software. The labial intrusion force and lingual retraction force were simulatively loaded to obtain initial displacement of the anterior teeth and the stresses of each tooth root and periodontal ligament, using three-dimensional finite element calculation software Ansys Workbench 15. The initial displacement of the lateral incisors was close to the bodily movement; and central incisors and lateral incisors slightly extruded. Compared with group A and group C, canine teeth appeared obviously horizontal "arched effect" by crown labial tipping in group B. The stress distribution of the tooth root and periodontal ligament was minimal and uniform in the group C. The 0.016 × 0.022- in stainless steel rectangular wire combined with 0.016- in stainless steel round wire used in the anterior teeth can better control the torque of the maxillary anterior teeth for space close in lingual orthodontics. Moreover, the stress distribution of tooth root and periodontal ligament is even, which is difficult to damage the periodontal ligament or result in external resorption of tooth root.

Este estudio tuvo como objetivo establecer modelos tridimensionales de elementos finitos de microimplantes linguales de alambre recto e investigar los efectos de diferentes patrones de alambre en el desplazamiento inicial de los dientes maxilares anteriores y el estrés del ligamento periodontal y la raíz del diente durante la retracción lingual sobre los dientes anteriores del hueso maxilar en ortodoncia. Se establecieron modelos geométricos tridimensionales del hueso maxilar con dentición utilizando una exploración por tomografía computarizada de haz cónico. Tres tipos de modelos maxilares, incluidos los microimplantes y el dispositivo Duet-Slot Lingual Bracket con tres arcos diferentes (modelo A: 0.016 pulgada × 0.022 pulgada alambre cuadrado de acero inoxidable; modelo B: alambre redondo de acero inoxidable de 0.016 pulgadas; alambre cuadrado de acero inoxidable de 0.016 pulgada × 0.022 pulgada y alambre redondo de acero inoxidable de 0.016 pulgada) ensamblados por el software Unigraphics NX 8.5. La fuerza de intrusión labial y la fuerza de retracción lingual se cargó simultáneamente, para obtener el desplazamiento inicial de los dientes anteriores y las tensiones de cada raíz dental y ligamento periodontal, usando el software tridimensional de cálculo de elementos finitos Ansys Workbench 15. El desplazamiento inicial de los incisivos laterales se relacionaba al movimiento corporal; mientra que los incisivos centrales e incisivos laterales se mostraron ligeramente extruidos. Comparado con el grupo A y el grupo C, los dientes caninos presentaron un "efecto arqueado" horizontal por la inclinación labial de la corona en el grupo B. La distribución del estrés de la raíz del diente y el ligamento periodontal fue mínima y uniforme en el grupo C. El alambre rectangular de acero inoxidable combinado con el alambre redondo de acero inoxidable de 0.016 usado en los dientes anteriores puede controlar mejor el torque de los dientes maxilares anteriores para cerrar el espacio en ortodoncia lingual. Además, la distribución del estrés de la raíz del diente y del ligamento periodontal es pareja, lo que dificulta dañar el ligamento periodontal o provocar una resorción externa de la raíz del diente.

Comparison of deflection forces of esthetic archwires combined with ceramic brackets

Abstract Coated archwires and ceramic brackets have been developed to improve facial esthetics during orthodontic treatment. However, their mechanical behavior has been shown to be different from metallic archwires and brackets. Therefore, the aim of this study was to compare the deflection forces in coated nickel-titanium (NiTi) and esthetic archwires combined with ceramic brackets. Material and Methods Non-coated NiTi (NC), rhodium coated NiTi (RC), teflon coated NiTi (TC), epoxy coated NiTi (EC), fiber-reinforced polymer (FRP), and the three different conventional brackets metal-insert polycrystalline ceramic (MI-PC), polycrystalline ceramic (PC) and monocrystalline ceramic (MC) were used. The specimens were set up on a clinical simulation device and evaluated in a Universal Testing Machine (Instron). An acrylic device, representative of the right maxillary central incisor was buccolingually activated and the unloading forces generated were recorded at 3, 2, 1 and 0.5 mm. The speed of the testing machine was 2 mm/min. ANOVA and Tukey tests were used to compare the different archwires and brackets. Results The brackets presented the following decreasing force ranking: monocrystalline, polycrystalline and polycrystalline metal-insert. The decreasing force ranking of the archwires was: rhodium coated NiTi (RC), non-coated NiTi (NC), teflon coated NiTi (TC), epoxy coated NiTi (EC) and fiber-reinforced polymer (FRP). At 3 mm of unloading the FRP archwire had a plastic deformation and produced an extremely low force in 2; 1 and 0.5 mm of unloading. Conclusion Combinations of the evaluated archwires and brackets will produce a force ranking proportional to the combination of their individual force rankings.

Effects of clinical use and sterilization on surface topography and surface roughness of three commonly used types of orthodontic archwires.

Aim: To evaluate the changes in surface topography and roughness of stainless steel (SS), nickel‑titanium and beta‑titanium (β‑Ti) archwires after clinical use and sterilization. Settings and Design: Thirty wires each of SS, nitinol, and β‑Ti (3M Unitek) were tested in as received, as received and autoclaved, and clinically retrieved then autoclaved conditions. Materials and Methods: A sterilization protocol of 134°C for 18 min was performed using an autoclave. Surface topography of specimens from each subgroup was examined using an environmental scanning electron microscope (ESEM model Quanta 200, The Netherlands) at ×100, ×1000, and ×2500 magnifications. Surface roughness was measured using arithmetic mean roughness (Ra) values obtained from optical profilometric scanning (Taylor Hobson, Leicester, UK). Statistical Analysis: Data were analyzed by one‑way analysis of variance and Tukey’s post‑hoc procedures. Results: Scanning electron microscope images revealed an increase in surface irregularities in SS and nitinol wires after clinical use. There was a significant increase in Ra values of SS orthodontic wires after intra‑oral exposure (P = 0.0002). Conclusion: Surface roughness of SS wires increased significantly after clinical use. Autoclave sterilization did not affect considerably on surface characteristics of any archwire.

Comparison of the frictional characteristics of aesthetic orthodontic brackets measured using a modified in vitro technique / 대한치과교정학회지

OBJECTIVE: The coefficients of friction (COFs) of aesthetic ceramic and stainless steel brackets used in conjunction with stainless steel archwires were investigated using a modified linear tribometer and special computer software, and the effects of the bracket slot size (0.018 inches [in] or 0.022 in) and materials (ceramic or metal) on the COF were determined. METHODS: Four types of ceramic (one with a stainless steel slot) and one conventional stainless steel bracket were tested with two types of archwire sizes: a 0.017 x 0.025-in wire in the 0.018-in slots and a 0.019 x 0.025-in wire in the 0.022-in slot brackets. For pairwise comparisons between the 0.018-in and 0.022-in slot sizes in the same bracket, an independent sample t-test was used. One-way and two-way analysis of variance (ANOVA) and Tukey's post-hoc test at the 95% confidence level (alpha = 0.05) were also used for statistical analyses. RESULTS: There were significant differences between the 0.022-in and 0.018-in slot sizes for the same brand of bracket. ANOVA also showed that both slot size and bracket slot material had significant effects on COF values (p < 0.001). The ceramic bracket with a 0.022-in stainless steel slot showed the lowest mean COF (micro = 0.18), followed by the conventional stainless steel bracket with a 0.022-in slot (micro = 0.21). The monocrystalline alumina ceramic bracket with a 0.018-in slot had the highest COF (micro = 0.85). CONCLUSIONS: Brackets with stainless steel slots exhibit lower COFs than ceramic slot brackets. All brackets show lower COFs as the slot size increases.

Mechanical properties of NiTi and CuNiTi shape-memory wires used in orthodontic treatment. Part 1: stress-strain tests

OBJECTIVE: This research aimed to compare, through traction tests, eight types of superelastic and heat-activated NiTi archwires, by six trade companies (GAC, TP, Ormco, Masel, Morelli and Unitek) to those with addition of copper (CuNiTi 27ºC and 35ºC, Ormco). METHODS: The tests were performed in an EMIC mechanical testing machine, model DL10000, capacity of 10 tons, at the Military Institute of Engineering (IME). RESULTS: The results showed that, generally, heat-activated NiTi archwires presented slighter deactivation loadings in relation to superelastic. Among the archwires that presented deactivation loadings biologically more adequate are the heat-activated by GAC and by Unitek. Among the superelastic NiTi, the CuNiTi 27ºC by Ormco were the ones that presented slighter deactivation loadings, being statistically (ANOVA) similar, to the ones presented by the heat-activated NiTi archwires by Unitek. When compared the CuNiTi 27ºC and 35ºC archwires, it was observed that the 27ºC presented deactivation forces of, nearly, ⅓ of the presented by the 35ºC. CONCLUSION: It was concluded that the CuNiTi 35ºC archwires presented deactivation loadings biologically less favorable in relation to the other heat-activated NiTi archwires, associated to lower percentage of deformation, on the constant baselines of deactivation, showing less adequate mechanical behavior, under traction, in relation to the other archwires.

OBJETIVO: o objetivo dessa pesquisa foi comparar, por meio de ensaios de tração, oito tipos de fios de NiTi superelásticos e termoativados, de seis empresas comerciais (GAC, TP, Ormco, Masel, Morelli e Unitek) àqueles com adição de cobre (CuNiTi 27ºC e 35ºC, da ORMCO). MÉTODOS: os ensaios foram realizados em máquina de ensaios mecânicos, da marca EMIC, modelo DL10000, de 10 toneladas de capacidade, no Instituto Militar de Engenharia (IME). RESULTADOS: os resultados mostraram que, de forma geral, os fios de NiTi termoativados apresentaram cargas mais suaves de desativação que os superelásticos. Entre os fios que apresentaram as cargas de desativação biologicamente mais adequadas, estão os termoativados da GAC e da Unitek. Entre os fios de NiTi superelásticos, os de CuNiTi 27ºC da Ormco foram os que apresentaram as cargas mais suaves de desativação, sendo estatisticamente semelhantes (ANOVA) às apresentadas pelos fios de NiTi termoativados da Unitek. Quando comparados os fios de CuNiTi 27ºC aos de 35ºC, observou-se que os primeiros apresentaram forças de desativação de, aproximadamente, ⅓ das apresentadas pelos últimos. CONCLUSÃO: conclui-se que os fios de CuNiTi 35ºC apresentaram cargas de desativação biologicamente menos favoráveis em relação aos demais fios de NiTi termoativados, sendo associadas a percentuais inferiores de deformação, nos patamares constantes de desativação, demonstrando comportamento mecânico, sob tração, menos adequado em relação aos demais fios.

In vitro force delivery of nickel-titanium superelastic archwires in vertical displacement

OBJECTIVE: The purpose of this study was to evaluate the force delivered by different superlastic nickel-titanium wires during vertical displacement, in order to determine whether their stress release meets the criteria for constant and light forces that are usually accredited to these archwires. METHOD: Ten samples of 6 brands of 0.016-in archwires (Ormco, GAC, Morelli, TP, American Orthodontics e Rocky Mountain) were tested in a complete metal model using Dynalock brackets (3M Unitek™). In the canine position, there was a sliding bracket connected to a pole. This set was related to a load cell of 0.5 kg attached to a universal testing machine (Autograph AG-199kNG, Shimadzu). The crosshead speed was 0.5 mm/min and the maximum displacement was 1.0 mm. The model was submerged in temperature-controlled water. The results were analyzed by ANOVA (p < 0.05), using the software SAS System 8.02, Cry, NC, USA. RESULTS: The TP archwire had the lowest force throughout the test, although the final force was high (277.91 g). The Rocky Mountain archwire had the highest force release (455.41 g). CONCLUSION: The different brands of wires tested in this study failed in delivering low and constant forces as expected from superlastic nickel-titanium wires. The forces were extremely heavy for a vertical tooth movement.

OBJETIVO: o objetivo deste estudo foi avaliar a força liberada por diferentes fios de níquel-titânio (NiTi) superelástico em deslocamento vertical, a fim de determinar se a liberação de estresse por esses satisfaz o critério de forças suaves e constantes, geralmente atribuído a tais arcos. MÉTODOS: dez amostras de seis arcos de NiTi superelástico 0,016” de marcas comerciais diferentes (Ormco, GAC, Morelli, TP, American Orthodontics e Rocky Mountain) foram testados em um modelo metálico usando braquetes Dynalock (3M Unitek). Na região do canino, havia um braquete móvel conectado a uma haste, a qual estava relacionada com uma célula de carga de 0,5kg de uma máquina universal de ensaios (Autograph AG-199kNG, Shimadzu). O deslocamento do conjunto na região do canino foi realizado a uma velocidade constante de 0,5mm/min e o deslocamento máximo foi de 1,0mm. O conjunto foi submerso em água com temperatura controlada a 37ºC. RESULTADOS: os resultados obtidos foram avaliados por ANOVA (p <0,05), usando o software SAS System 8.02, Cry, NC, EUA. O arco da TP apresentou a menor força durante todo o teste, embora a força final tenha sido elevada (277,91g). O fio da Rocky Mountain demonstrou a maior liberação de força (455,41g). CONCLUSÕES: conclui-se que todas as diferentes marcas comerciais testadas nesse estudo falharam em liberar forças baixas e constantes, como é esperado nos fios de níquel-titânio superelástico. As forças foram extremamente pesadas para o movimento vertical de dentes.

Ortodontia lingual com sistema 2D / 2D Lingual Orthodontics

A Ortodontia lingual é uma alternativa no tratamento de pacientes adultos que desejam aparelhos ortodônticos totalmente invisíveis. A técnica lingual 2D emprega conhecimentos e procedimentos clínicos exclusivamente com os braquetes linguais 2D e permite que se obtenha uma oclusão bastante funcional e estética, mesmo em casos de má-oclusão severa, pois utiliza os princípios de biomecânica lingual. Esta é uma técnica simplificada que possibilita a colagem direta dos braquetes, sem a necessidade de se fazer o set up convencional.

2D Lingual Orthodontics is the array of knowledge and clinical procedures adopted and finalized exclusively for the use and application of 2D Lingual braquetes. It represents a valuable alternative to treat adult patients, who demand a completely invisible orthodontic appliance. The ease of direct application of 2D lingual braquetes makes it possible to achieve a good functional and esthetic occlusion also in the presence of severe malocclusions, adopting the biomechanical options offered by lingual appliances, in addition to the improved esthetics during the active phase of treatment.

Efeitos dos fios de nivelamento de níquel-titânio e de aço inoxidável na posição dos incisivos inferiores / Effects of nickel-titanium and stainless steel leveling wires on the position of mandibular incisors

OBJETIVO: estudar os efeitos do nivelamento realizado com fios de NiTi termoativado e de aço inoxidável, avaliando-se as possíveis alterações na posição dos incisivos inferiores, em casos com extrações, correlacionando com o tempo de tratamento. MÉTODOS: a amostra foi composta de 36 indivíduos, de ambos os sexos, leucodermas brasileiros, com idade média inicial de 15 anos e 5 meses, portadores de más oclusões de Classes I e II, distribuídos em dois grupos. No Grupo 1 (n=17), o nivelamento foi realizado com a sequência 1, utilizando-se três fios - 0,016" e 0,019"x0,025" de NiTi termoativado, e 0,019"x0,025" de aço inoxidável. No Grupo 2 (n=19), foi testada a sequência 2, na qual foram utilizados apenas fios de aço inoxidável (0,014"; 0,016"; 0,018"; 0,020" e 0,019"x0,025" com torque passivo nos incisivos inferiores). Os dados foram coletados utilizando-se o método cefalométrico computadorizado e comparados pelo teste t de Student com o nível de significância de 5 por cento. RESULTADOS: no Grupo 1, os incisivos inferiores inclinaram-se para lingual, com movimento significativo apenas da coroa (1,6mm). No Grupo 2, os incisivos inferiores permaneceram estáveis. Não houve alteração vertical em nenhum dos grupos. CONCLUSÕES: a sequência 2 proporcionou um melhor controle dos incisivos inferiores, não alterando suas posições iniciais, enquanto a sequência 1 permitiu a expressão do torque da prescrição utilizada, levando a uma inclinação lingual desses dentes. O tempo de tratamento foi menor utilizando-se a sequência 1. As variações biomecânicas estudadas apresentaram vantagens e desvantagens que devem ser conhecidas e ponderadas pelo ortodontista no planejamento do caso.

OBJECTIVE: Investigate the effects of heat-activated NiTi and stainless steel wires to evaluate potential changes in the position of mandibular incisors in extraction cases as correlated with treatment length.METHOD: The sample consisted of 36 individuals of both genders, Brazilian Caucasians with mean initial age of 15 years and 5 months with Class I and Class II malocclusions, divided into two groups. In Group 1 (n=17) leveling was performed with Sequence 1, comprised of three different wire cross-sections: 0.016-in and 0.019 x 0.025-in heat-activated NiTi wires and 0.019 x 0.025-in stainless steel wires. In Group 2 (n=19) Sequence 2 was tested using only stainless steel wires (0.014-in, 0.016-in, 0.018-in, 0.020-in and 0.019 x 0,025-in) with passive torque in the mandibular incisors. Data were collected using computerized cephalometry and compared using Student's t-test with 5% significance level.RESULTS: In Group 1, mandibular incisors were inclined lingually although only the crowns showed significant movement (1.6 mm). In Group 2, mandibular incisors remained stable. No vertical changes were noted in either group.CONCLUSIONS: Sequence 2 yielded better mandibular incisor control with no changes in their initial positions, while Sequence 1 allowed torques in the bracket prescription to be expressed, leading to the lingual inclination of these teeth. Treatment length was shorter when Sequence 1 was used. The evaluated biomechanic variations presented advantages and disadvantages that should be known and considered by the orthodontist during treatment planning.

A comparative evaluation of metallurgical properties of stainless steel and TMA archwires with timolium and titanium niobium archwires - An in vitro study.

Objectives: This study aims to evaluate and compare the mechanical and metallurgical properties of stainless steel and titanium molybdenum alloy (TMA) archwires, with recently introduced timolium and titanium niobium arch wires. Materials and Methods: Archwires were categorized into four groups (group I to IV) with 10 samples in each group. They were evaluated for tensile strength, yield strength, modulus of elasticity, load deflection, frictional properties and weld characteristics. Results: The results were statistically analyzed using ANOVA test and it indicated that stainless steel has high strength, high stiffness and low friction compared to other arch wires, thereby proving that it is the best choice for both sliding as well as frictionless retraction mechanics. TMA with its high formability, low stiffness and low load deflection property is suited to apply consistent force in malaligned teeth but, high friction limits its use in retraction only with loop mechanics. Conclusion: Timolium possesses comparatively low stiffness, better strength and behaves as an intermediate between stainless steel and TMA and hence can be tried for almost all clinical situations. Low springback and high formability of titanium-niobium archwire allows creation of finishing bends and thus it can be used as finishing archwire.

Three-dimensional finite element analysis of the phenomenon produced during retraction of four maxillary incisors / 대한치과교정학회지

This study was designed to investigate force systems and tooth movements produced by retraction archwire during retraction of four maxillary incisors after the maxillary canine retraction into the maxillary first premolar extraction space using the computer-aided three-dimensional finite element method. A three-dimensional finite element model, consisting of 2248 elements and 3194 nodes, was constructed. The model consisted of maxillary teeth and surrounding periodontal membranes, .022" x .028" -slot brackets, and 5 types of retraction archwires(.019" x .025" stainless steel archwire) modeled using the beam elements. The contact between the wire and the bracket slot was modeled using the gap elements because of the non-linear elastic behaviors of the contact between them. The forces and moments, and displacements produced by retraction archwire were measured at various conditions to investigate the difference according to types of loops, magnitudes of activation force, gable angle, and anterior lingual root torque. The results were expressed quantitative and visual ways in the three-dimensional method. The following conclusions can be drawn from this study: 1. When the tear-drop loop archwire was activated, the mesio-distal and lingual translational movements of the teeth helped to close the extraction space, but unwanted movements of the teeth including intrusions and extrusions, and rotational movements in each direction occurred. 2. Activation of T-loop archwire compared with those of other types of retraction archwires produced the least translational movements of the teeth helped to space closure and also the least unwanted movements of the teeth. 3. Increasing amount of activation in the tear-drop archwire led not only to increase of translational movements of the teeth helped to space closure, but also to increase of unwanted movements of the teeth. 4. Addition of gable bend in the tear-drop archwire helped anterior teeth to translational movements in the mesio-distal direction, but increased unwanted movements of the teeth. 5. Addition of anterior lingual root torque in the tear-drop archwire helped central and lateral incisor to improve their facio-lingual inclination, but increased unwanted movements of the teeth.